Council Regulation (EU) No 333/2011
of 31 March 2011
establishing criteria determining when certain types of scrap metal cease to be waste under Directive 2008/98/EC of the European Parliament and of the Councilcross-notes
THE COUNCIL OF THE EUROPEAN UNION,
Having regard to the Treaty on the Functioning of the European Union,
Having regard to Directive 2008/98/EC of the European Parliament and of the Council of 19 November 2008 on waste and repealing certain Directives(1) and in particular Article 6(2) thereof,
Having regard to the proposal from the European Commission,
After submission of the proposed measures to the European Parliament,
Whereas:
(1) It results from an evaluation of several waste streams that recycling markets for scrap metal would benefit from the development of specific criteria determining when scrap metal obtained from waste ceases to be waste. Those criteria should ensure a high level of environmental protection. They should be without prejudice to the classification of scrap metal as waste by third countries.
(2) Reports of the Joint Research Centre of the European Commission have shown that a market and demand exist for iron, steel and aluminium scrap to be used as feedstock in steel works, foundries, aluminium refiners and remelters for the production of metals. Iron, steel and aluminium scrap should therefore be sufficiently pure and meet the relevant scrap standards or specifications required by the metal producing industry.
(3) The criteria determining when iron, steel and aluminium scrap cease to be waste should ensure that iron, steel and aluminium scrap resulting from a recovery operation meet the technical requirements of the metal producing industry, comply with existing legislation and standards applicable to products and do not lead to overall adverse environmental or human health impacts. Reports of the Joint Research Centre of the European Commission have shown that the proposed criteria on the waste used as input in the recovery operation, on the treatment processes and techniques, as well as on the scrap metal resulting from the recovery operation, fulfil those objectives since they should result in the production of iron, steel and aluminium scrap devoid of hazardous properties and sufficiently free of non-metallic compounds.
(4) In order to ensure compliance with the criteria, it is appropriate to provide that information on scrap metal which has ceased to be waste is issued and that a quality management system is implemented.
(5) A review of the criteria may prove necessary if, on the basis of a monitoring of the development of market conditions for iron and steel scrap and aluminium scrap, adverse effects on recycling markets for iron and steel scrap and aluminium scrap are noted, in particular with regard to the availability of, and access to, such scrap.
(6) In order to allow operators to adapt to the criteria determining when scrap metal ceases to be waste, it is appropriate to provide for a reasonable period to elapse before this Regulation applies.
(7) The Committee established by Article 39(1) of Directive 2008/98/EC has not delivered an opinion on the measures provided for in this Regulation and the Commission therefore submitted to the Council a proposal relating to the measures and forwarded it to the European Parliament.
(8) The European Parliament has not opposed the proposed measures,
HAS ADOPTED THIS REGULATION:
Article 1 Subject matter
This Regulation establishes criteria determining when iron, steel and aluminium scrap, including aluminium alloy scrap, cease to be waste.
Article 2 Definitions
[F1 1.F1] For the purposes of this Regulation, the definitions set out in Directive 2008/98/EC shall apply.
In addition, the following definitions shall apply:
‘iron and steel scrap’ means scrap metal which consists mainly of iron and steel;
‘aluminium scrap’ means scrap metal which consists mainly of aluminium and aluminium alloy;
‘holder’ means the natural or legal person who is in possession of scrap metal;
‘producer’ means the holder who transfers scrap metal to another holder for the first time as scrap metal which has ceased to be waste;
‘importer’ means any natural or legal person established within the [F2 United Kingdom F2] who introduces scrap metal which has ceased to be waste into the [F3 United Kingdom F3] ;
‘qualified staff’ means staff which is qualified by experience or training to monitor and assess the properties of scrap metal;
‘visual inspection’ means inspection of scrap metal covering all parts of a consignment and using human senses or any non-specialised equipment;
‘consignment’ means a batch of scrap metal which is intended for delivery from a producer to another holder and may be contained in either one or several transport units, such as containers.
[F4 “ competent authority ” means—
in relation to England, the Environment Agency;
in relation to Wales, the Natural Resources Body for Wales;
in relation to Scotland, the Scottish Environment Protection Agency;
in relation to Northern Ireland, the Department of Agriculture, Environment and Rural Affairs;
“ EU-derived domestic legislation ” has the meaning given by section 2(2) of the European Union (Withdrawal) Act 2018 ;
“ local authority ” means—
in England outside Greater London—
-
— a district council,
-
— a county council, or
-
— the Council of the Isles of Scilly;
in England outside Greater London—
-
— the council of a London borough,
-
— the Common Council of the City of London,
-
— the Sub-Treasurer of the Inner Temple, or
-
— the Under-Treasurer of the Middle Temple;
in Wales—
-
— a county council, or
-
— a county borough council;
in Scotland, a council constituted under section 2 of the Local Government etc. (Scotland) Act 1994;
in Northern Ireland, a district council established under section 1 of the Local Government Act (Northern Ireland) 1972.F4]
[F5Article 2A Modification of Directive 2008/98/EC of the European Parliament and of the Council
1.For the purposes of this Regulation, a reference to Directive 2008/98/EC is a reference to Directive 2008/98/EC of the European Parliament and of the Council on waste, as last amended by Directive (EU) 2018/851, and read in accordance with this Article.
2.A reference to one or more member States in a provision imposing an obligation or conferring a discretion on a member State or member States is to be read as a reference to the competent authority, appropriate authority or local authority which, immediately before IP completion day, was responsible for the United Kingdom's compliance with that obligation or able to exercise that discretion.
3.Article 2 is to be read as if—
(a)in paragraph 2—
(i) in the words before point (a), for “other Community legislation” there were substituted “ [F6 assimilated F6] law ” ;
(ii) in points (b) and (c), for “Regulation (EC) No 1774/2002 ” there were substituted “ Regulation (EC) No 1069/2009 ” ;
(iii) in point (d), as it extends to England and Wales, for the words from “Directive 2006/21/EC ” to the end there were substituted “ the Mining Waste Directive ” ;
(iv)for point (d), as it extends to Scotland, there were substituted—
“(d)extractive waste, which has the same meaning as in regulation 2(1) of the Management of Extractive Waste (Scotland) Regulations 2010.”;
(v)for point (d), as it extends to Northern Ireland, there were substituted—
“(d)extractive waste, which has the same meaning as in regulation 2(2) of the Planning (Management of Waste from Extractive Industries) Regulations (Northern Ireland) 2015.”;
(b) in paragraph 3, the words from “Without prejudice” to “Community legislation,” were omitted;
(c)paragraph 4 were omitted.
4. Article 3(20) is to be read as if for “Article 2(11) of Directive 96/61/EC ” there were substituted “ Article 3(10) of the Industrial Emissions Directive ” .
5. Article 5 is to be read as if—
(a) in paragraph 1, “Member States shall take appropriate measures to ensure that” were omitted;
(b)after paragraph 1 there were inserted—
“1A.
Any decision as to whether a substance or object is a by-product must be made—
(a)in accordance with any regulations setting out detailed criteria on the application of the conditions in paragraph 1 to specific substances or objects; and
(b)having regard to any guidance published by the appropriate authority or the competent authority for the purposes of this Article.”;
(c)paragraphs 2 and 3 were omitted.
6.Article 6 is to be read as if—
(a) in paragraph 1, “Member States shall take appropriate measures to ensure that” were omitted;
(b)after paragraph 1 there were inserted—
“1A.
Any decision as to whether a substance or object has ceased to be waste must be made—
(a)in accordance with any regulations or [F7assimilated directF7] legislation setting out detailed criteria on the application of the conditions in paragraph 1 to specific types of waste; and
(b)having regard to any guidance published by the appropriate authority or the competent authority for the purposes of this Article.”;
(c)in paragraph 2—
(i)the first subparagraph were omitted;
(ii) in the second subparagraph, for “Those detailed criteria” there were substituted “Any detailed criteria set out in guidance as referred to in paragraph 1A”;
(iii)the third and fourth subparagraphs were omitted;
(d)paragraph 3 were omitted;
(e)in paragraph 4—
(i)in the first subparagraph—
(aa) in the first sentence, for the words from the beginning to “Member State”, there were substituted “Where criteria have not been set out as referred to in paragraph 1A(a), the competent authority”;
(bb)the second sentence were omitted;
(ii)in the second subparagraph—
(aa) for “Member States” there were substituted “The competent authority”;
(bb) “by competent authorities” were omitted.
7.Article 7 is to be read as if—
(a)before paragraph 1 there were inserted—
“A1.
In this Article, the “list of waste” means the list contained in the Annex to Commission Decision 2000/532/EC, as that list has effect in England, Wales, Scotland or Northern Ireland (as the case may be).”;
(b)in paragraph 1—
(i)the first and second sentences were omitted;
(ii)for the third sentence there were substituted “The list of waste shall, except as provided in Commission Decision 2000/532/EC, be binding as regards determination of the waste which is to be considered as hazardous waste or as non-hazardous waste.”;
(c)paragraphs 2, 3, 6 and 7 were omitted.
8. Annex 3 is to be read as if, in entry HP 9, in the second sentence, “in the Member States” were omitted.
9. In this Article, “ the appropriate authority ” means—
(a)in relation to England, the Secretary of State;
(b)in relation to Wales, the Welsh Ministers;
(c)in relation to Scotland, the Scottish Environment Protection Agency;
(d)in relation to Northern Ireland, the Department of Agriculture, Environment and Rural Affairs.F5]
[F5Article 2B Meaning of “the Mining Waste Directive” and “the Industrial Emissions Directive”
1. In Article 2A(3)(a)(iii), “ the Mining Waste Directive ” means Directive 2006/21/EC of the European Parliament and of the Council on the management of waste from extractive industries, read in accordance with paragraphs 2 and 3.
2.Article 2 is to be read as if—
(a)in paragraph 2(c), the reference to Article 11(3)(j) of Directive 2000/60/EC were a reference to that Article read in accordance with paragraph 7 of this Article;
(b)paragraphs 3 and 4 were omitted.
3. Article 3(1) is to be read as if, for “Article 1(a) of Directive 75/442/EEC ” there were substituted “ Article 3(1) of Directive 2008/98/EC , as read with Articles 5 and 6 of that Directive ” .
4. In Article 2A(4), “ the Industrial Emissions Directive ” means Directive 2010/75/EU of the European Parliament and of the Council on industrial emissions (integrated pollution prevention and control), read in accordance with paragraphs 5 and 6.
5.Article 3 is to be read as if—
(a) in point (1)(a), for the words from “Article 1” to the end there were substituted “ Article 4(78) of Council Directive 2013 /59/Euratom laying down basic safety standards for protection against the dangers arising from exposure to ionising radiation ” ;
(b) in point (10)(b), for “Member State in question” there were substituted “ United Kingdom ” ;
(c) in point (23), for the words from “point 1” to the end there were substituted “ point 1 of the second subparagraph of Article 2 of Council Directive 2009/158/EC on animal health conditions governing intra-Community trade in, and imports from third countries of, poultry and hatching eggs ” ;
(d) in point (37), for the words from “of the European” to the end there were substituted “ , read with Articles 5 and 6 of that Directive ” .
6.Annex 1 is to be read as if—
(a)in the words before point 1, the second paragraph were omitted;
(b)in point 5.3—
(i) in point (a), in the words before point (i), for “Council Directive 91/271/EEC of 21 May 1991 concerning urban waste-water treatment” there were substituted “ the Urban Waste Water Treatment (England and Wales) Regulations 1994 ” ;
(ii) in point (b), in the words before point (i), for “Directive 91/271/EEC ” there were substituted “ the Urban Waste Water Treatment (England and Wales) Regulations 1994 ” ;
(c)in point 5.4, the reference to Council Directive 1999/31/EC of 26 April 1999 on the landfill of waste were a reference to the Landfill Directive;
(d) in point 6.9, for “Directive 2009/31/EC ” there were substituted “ the EU-derived domestic legislation which transposed Directive 2009/31/EC in respect of England and Wales ” ;
(e) in point 6.11, for “Directive 91/271/EEC ” there were substituted “ the Urban Waste Water Treatment (England and Wales) Regulations 1994 ” .
7.For the purposes of paragraph 2(a), Article 11(3)(j) of Directive 2000/60/EC is to be read as if—
(a) the reference to “Member States” were a reference to the appropriate authority or the competent authority;
(b) in the words after the final indent, “environmental objectives”—
(i)in relation to the Northumbria River Basin District, means the environmental objectives referred to in the WFD Regulations as applied by regulation 5 of the Water Environment (Water Framework Directive) (Northumbria River Basin District) Regulations 2003;
(ii)in relation to the Solway Tweed River Basin District, has the same meaning as in regulation 2 of the Water Environment (Water Framework Directive) (Solway Tweed River Basin District) Regulations 2004;
(iii)in relation to a river basin district within the meaning of the WFD Regulations, has the same meaning as in those Regulations.
8. In paragraph 6(c), “the Landfill Directive” means Council Directive 1999/31/EC on the landfill of waste, as last amended by Directive (EU) 2018/850 , and read as if, in Article 2—
(a) in point (a) “‘waste’,” were omitted; and
(b)after point (a) there were inserted—
“(aa)“waste” means anything that—
(i)is waste within the meaning of Article 3(1) of Directive 2008/98/EC, as read with Articles 5 and 6 of that Directive, and
(ii)is not excluded from the scope of that Directive by Article 2(1), (2) or (3) of that Directive;”.
9.In paragraph 7—
(a) in point (a), “ the appropriate authority ” has the meaning given by Article 2A(9);
(b) in point (b), “ the WFD Regulations ” means the Water Environment (Water Framework Directive) (England and Wales) Regulations 2017 . F5]
Article 3 Criteria for iron and steel scrap
Iron and steel scrap shall cease to be waste where, upon transfer from the producer to another holder, all of the following conditions are fulfilled:
the waste used as input for the recovery operation complies with the criteria set out in Section 2 of Annex I;
the waste used as input for the recovery operation has been treated in accordance with the criteria set out in Section 3 of Annex I;
the iron and steel scrap resulting from the recovery operation complies with the criteria set out in Section 1 of Annex I;
the producer has satisfied the requirements set out in Articles 5 and 6.
Article 4 Criteria for aluminium scrap
Aluminium scrap, including aluminium alloy scrap, shall cease to be waste where, upon transfer from the producer to another holder, all of the following conditions are fulfilled:
the waste used as input in the recovery operation complies with the criteria set out in Section 2 of Annex II;
the waste used as input in the recovery operation has been treated in accordance with the criteria set out in Section 3 of Annex II;
the aluminium scrap resulting from the recovery operation complies with the criteria set out in Section 1 of Annex II;
the producer has satisfied the requirements set out in Articles 5 and 6.
Article 5 Statement of conformity
1.The producer or the importer shall issue, for each consignment of scrap metal, a statement of conformity in accordance with the model set out in Annex III.
2.The producer or the importer shall transmit the statement of conformity to the next holder of the scrap metal consignment. The producer or the importer shall retain a copy of the statement of conformity for at least 1 year after its date of issue and shall make it available to competent authorities upon request.
3.The statement of conformity may be in electronic form.
Article 6 Quality management
1.The producer shall implement a quality management system suitable to demonstrate compliance with the criteria referred to in Articles 3 and 4, respectively.
2.The quality management system shall include a set of documented procedures concerning each of the following aspects:
(a)acceptance control of waste used as input for the recovery operation as set out in Section 2 of Annexes I and II;
(b)monitoring of the treatment processes and techniques described in Section 3.3 of Annexes I and II;
(c)monitoring of the quality of scrap metal resulting from the recovery operation as set out in Section 1 of Annexes I and II (including sampling and analysis);
(d)effectiveness of the radiation monitoring as set out in Section 1.5 of Annexes I and II, respectively;
(e)feedback from customers concerning compliance with scrap metal quality;
(f)record keeping of the results of monitoring conducted under points (a) to (d);
(g)review and improvement of the quality management system;
(h)training of staff.
3.The quality management system shall also prescribe the specific monitoring requirements set out in Annexes I and II for each criterion.
4.Where any of the treatments referred to in Section 3.3 of Annex I or Section 3.3 of Annex II are carried out by a prior holder, the producer shall ensure that the supplier implement a quality management system which complies with the requirements of this Article.
5.F8A conformity assessment body, as defined in Regulation (EC) No 765/2008 of the European Parliament and of the Council of 9 July 2008 setting out the requirements for accreditation and market surveillance relating to the marketing of products(2), which has obtained accreditation in accordance with that Regulation ... shall verify that the quality management system complies with the requirements of this Article. The verification should be carried out every 3 years.
6.The importer shall require his suppliers to implement a quality management system which complies with the requirements of paragraphs 1, 2 and 3 of this Article and has been verified by an independent external verifier.
[F9 6A. In paragraph 6, “ independent external verifier ” means—
(a)a conformity assessment body as defined in Regulation (EC) No 765/2008;
(b)a conformity assessment body as defined in Regulation (EC) No 765/2008 as it has effect in EU law;
(c)any other environmental verifier as defined in Article 2(20)(b) of Regulation (EC) No 1221/2009 as it has effect in EU law.F9]
7.The producer shall give competent authorities access to the quality management system upon request.
[F10Article 6A EU exit: transitional provision
1.Paragraph 3 applies to verification obtained in compliance with Article 6 as it had effect immediately before IP completion day.
2.Paragraph 3 also applies where—
(a)before IP completion day, a producer or supplier has submitted a management system to a conformity assessment body or an environmental verifier for verification in compliance with Article 6 as it had effect immediately before IP completion day, and
(b)after IP completion day, the producer or supplier obtains that verification.
3.Where this paragraph applies, the verification obtained is deemed to be verification for the purposes of Article 6.
4. In paragraph 2, “ supplier ” means the supplier of a producer or of an importer. F10]
Article 7 Entry into force
F11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
F12 ...
Done at Brussels, 31 March 2011.
For the Council
The President
Völner P.
ANNEX I
Criteria for iron and steel scrap
|
a
Council Directive 96/29/Euratom of 13 May 1996 laying down basic safety standards for the protection of the health of workers and the general public against the dangers arising from ionizing radiation (OJ L 159, 29.6.1996, p. 1). |
|
|
b
Commission Decision 2000/532/EC of 3 May 2000 replacing Decision 94/3/EC establishing a list of wastes pursuant to Article 1(a) of Council Directive 75/442/EEC on waste and Council Decision 94/904/EC establishing a list of hazardous waste pursuant to Article 1(4) of Council Directive 91/689/EEC on hazardous waste (OJ L 226, 6.9.2000, p. 3). |
|
|
c
Regulation (EC) No 850/2004 of the European Parliament and of the Council of 29 April 2004 on persistent organic pollutants (OJ L 158, 30.4.2004, p. 7). |
|
|
d
OJ L 37, 13.2.2003, p. 24. |
|
|
e
OJ L 269, 21.10.2000, p. 34. |
|
| Criteria | Self-monitoring requirements |
|---|---|
| 1. Quality of scrap resulting from the recovery operation | |
1.1. The scrap shall be graded according to a customer specification, an industry specification or a standard for direct use in the production of metal substances or objects by steel works or foundries. |
Qualified staff shall grade each consignment. |
1.2. The total amount of foreign materials (steriles) shall be ≤ 2 % by weight.Foreign materials are: (1)
non-ferrous metals (excluding alloying elements in any ferrous metal substrate) and non-metallic materials such as earth, dust, insulation and glass; (2)
combustible non-metallic materials such as rubber, plastic, fabric, wood and other chemical or organic substances; (3)
larger pieces (brick-size) which are non-conductors of electricity such as tyres, pipes filled with cement, wood or concrete; (4)
residues arising from steel melting, heating, surface conditioning (including scarfing), grinding, sawing, welding and torch cutting operations, such as slag, mill scale, baghouse dust, grinder dust, sludge. |
Qualified staff shall carry out a visual inspection of each consignment. At appropriate intervals (at least every 6 months), representative samples of foreign materials shall be analysed by weighing after magnetic or manual (as appropriate) separation of iron and steel particles and objects under careful visual inspection. The appropriate frequencies of monitoring by sampling shall be established taking into account the following factors: (1)
the expected pattern of variability (for example as shown by historical results); (2)
the inherent risk of variability in the quality of waste used as input for the recovery operation and any subsequent processing; (3)
the inherent precision of the monitoring method; and (4)
the proximity of results to the limitation of the foreign materials’ content to a maximum of 2 % per weight. The process of determining monitoring frequencies should be documented as part of the quality management system and should be available for auditing. |
1.3. The scrap shall not contain excessive ferrous oxide in any form, except for typical amounts arising from outside storage of prepared scrap under normal atmospheric conditions. |
Qualified staff shall carry out a visual inspection for the presence of oxides. |
1.4. Scrap shall be free of visible oil, oily emulsions, lubricants or grease except negligible amounts that will not lead to any dripping. |
Qualified staff shall carry out a visual inspection of each consignment, paying particular attention to those parts where oil is most likely to drip. |
1.5. Radioactivity: there is no need for response action according to national or international rules on monitoring and response procedures for radioactive scrap metal.F13 ... |
Qualified staff shall monitor the radioactivity of each consignment. Each consignment of scrap shall be accompanied by a certificate established in accordance with national or international rules on monitoring and response procedures for radioactive scrap metal. The certificate may be included in other documentation accompanying the consignment. |
1.6. The scrap shall not display any of the hazardous properties listed in Annex III to Directive 2008/98/EC. The scrap shall comply with the concentration limits laid down in Decision 2000/532/ECb and shall not exceed the concentration limits laid down in Annex IV to Regulation (EC) No 850/2004c.Properties of individual elements included in iron and steel alloys are not relevant for this requirement. |
Qualified staff shall carry out a visual inspection of each consignment. Where visual inspection raises any suspicion of possible hazardous properties, further appropriate monitoring measures shall be taken, such as sampling and testing where appropriate. The staff shall be trained on potential hazardous properties that may be associated with iron and steel scrap and on material components or features that allow hazardous properties to be recognised. The procedure for recognising hazardous materials shall be documented under the quality management system. |
1.7. The scrap shall not contain any pressurised, closed or insufficiently open containers that could cause an explosion in a metalwork furnace. |
Qualified staff shall carry out a visual inspection of each consignment. |
| 2. Waste used as input for the recovery operation | |
2.1. Only waste containing recoverable iron or steel may be used as input.2.2. Hazardous waste shall not be used as an input except where proof is provided that the processes and techniques specified in Section 3 of this Annex to remove all hazardous properties have been applied.2.3. The following waste shall not be used as an input: (a)
filings and turnings that contain fluids such as oil or oily emulsions; and (b)
barrels and containers, except equipment from end-of-life vehicles, which contain or have contained oil or paints. |
Acceptance control of all waste received (by visual inspection) and of the accompanying documentation shall be carried out by qualified staff which is trained on how to recognise waste that does not meet the criteria set out in this Section. |
| 3. Treatment processes and techniques | |
3.1. The iron or steel scrap shall have been segregated at source or while collecting and shall have been kept separate or the input waste shall have been treated to separate the iron and steel scrap from the non-metal and non-ferrous components.3.2. All mechanical treatments (like cutting, shearing, shredding or granulating; sorting, separating, cleaning, de-polluting, emptying) needed to prepare the scrap metal for direct input into final use in steel works and foundries shall have been completed.3.3. For waste containing hazardous components, the following specific requirements shall apply: (a)
input materials that originate from waste electrical or electronic equipment or from end-of-life vehicles shall have undergone all treatments required by [F14the EU-derived domestic legislation that transposed— (i)
Article 6 of Directive 2000/53/EC of the European Parliament and of the Council on end-of life vehicles, as last amended by Commission Directive (EU) 2017/2096, and (ii)
Article 8 of Directive 2012/19/EU of the European Parliament and of the Council on waste electrical and electronic equipment (WEEE), as it had effect immediately before 4th July 2018.F14] (b)
chlorofluorocarbons in discarded equipment shall have been captured in a process approved by the competent authorities; (c)
cables shall have been stripped or chopped. If a cable contains organic coatings (plastics), the organic coatings shall have been removed in accordance with the best available techniques; (d)
barrels and containers shall have been emptied and cleaned, and (e)
hazardous substances in waste that is not mentioned in point (a) shall have been efficiently removed in a process which is approved by the competent authority. |
|
ANNEX II
Criteria for aluminium scrap
|
a
EN 13920-1:2002; Aluminium and aluminium alloys – Scrap- Part 1: General requirements, sampling and tests; CEN 2002. |
|
|
b
OJ L 159, 29.6.1996, p. 1. |
|
|
c
OJ L 226, 6.9.2000, p. 3. |
|
|
d
OJ L 229, 30.4.2004, p. 1. |
|
|
e
OJ L 37, 13.2.2003, p. 24. |
|
|
f
OJ L 269, 21.10.2000, p. 34. |
|
| Criteria | Self-monitoring requirements |
|---|---|
| 1. Scrap quality | |
1.1. The scrap shall be graded in accordance with a customer specification, an industry specification or a standard for direct use in the production of metal substance or objects by refining or re-melting. |
Qualified staff shall grade each consignment. |
1.2. The total amount of foreign materials shall be ≤ 5 % by weight or the metal yield shall be ≥ 90 %;Foreign materials are: (1)
metals other than aluminium and aluminium alloys; (2)
non-metallic materials such as earth, dust, insulation materials and glass; (3)
combustible non-metallic materials such as rubber, plastic, fabric, wood and other chemical or organic substances; (4)
larger pieces (brick-size) which are non-conductors of electricity such as tyres, pipes filled with cement, wood or concrete; or (5)
residues arising from the melting of aluminium and aluminium alloys, heating, surface conditioning (including scarfing), grinding, sawing, welding and torch cutting operations such as slag, dross, skimmings, baghouse dust, grinder dust, sludge. |
The producer of the aluminium scrap shall check compliance by monitoring the amount of foreign materials or by determining the metal yield. Qualified staff shall carry out visual inspection of each consignment. At appropriate intervals (at least every 6 months), representative samples of each grade of aluminium scrap shall be analysed to measure the total amount of foreign materials or the metal yield. The representative samples shall be obtained in accordance with the sampling procedures described in standard EN 13920a. The total amount of foreign materials shall be measured by weight after separating aluminium metallic particles and objects from particles and objects consisting of foreign materials by hand sorting or other means of separation (such as by magnet or by using density as a basis). Metal yield shall be measured in accordance with the following procedure: (1)
determination of mass (m1) after removal and determination of moisture (in accordance with point 7.1 of the EN 13920-1:2002 standard); (2)
removal and determination of free iron (in accordance with point 7.2 of the EN 13920-1:2002 standard); (3)
determination of the mass of the metal after melting and solidifying (m2) following the procedure for the determination of the metal yield in accordance with point 7.3 of the EN 13920-1:2002 standard; (4)
calculation of the metal yield m [%] = (m2/m1) × 100. The appropriate frequencies of analysis of representative samples shall be established taking into account the following factors: (1)
the expected pattern of variability (such as shown by historical results); (2)
the inherent risk of variability in the quality of waste used as input for the recovery operation and in the performance of the treatment processes; (3)
the inherent precision of the monitoring method; and (4)
the proximity of results to the limit values for the total amount of foreign materials or the metal yield. |
1.3. The scrap shall not contain polyvinyl chloride (PVC) in form of coatings, paints, plastics. |
Qualified staff shall carry out a visual inspection of each consignment. |
1.4. The Scrap shall be free of visible oil, oily emulsions, lubricants or grease except negligible amounts that will not lead to any dripping. |
Qualified staff shall carry out a visual inspection of each consignment, paying particular attention to those parts where oil is most likely to drip. |
1.5. Radioactivity: there is no need for response action according to national or international rules on monitoring and response procedures for radioactive scrap metal.F15 ... |
Qualified staff shall monitor the radioactivity of each consignment. Each consignment of scrap shall be accompanied by a certificate established in accordance with national or international rules on monitoring and response procedures for radioactive scrap metal. The certificate may be included in other documentation accompanying the consignment. |
1.6. The scrap shall not display any of the hazardous properties listed in Annex III to Directive 2008/98/EC. The scrap shall comply with the concentration limits laid down in Commission Decision 2000/532/ECc and shall not exceed the concentration limits laid down in Annex IV to Regulation (EC) No 850/2004d.Properties of individual elements included in aluminium alloys are not relevant for this requirement. |
Qualified staff shall carry out a visual inspection of each consignment. Where visual inspection raises any suspicion of possible hazardous properties, further appropriate monitoring measures shall be taken, such as sampling and testing where appropriate. Staff shall be trained on potential hazardous properties that may be associated with aluminium scrap and on material components or features that allow hazardous properties to be recognised. The procedure for recognising hazardous materials shall be documented under the quality management system. |
1.7. The scrap shall not contain any pressurised, closed or insufficiently open containers that could cause an explosion in a metalwork furnace. |
Qualified staff shall carry out a visual inspection of each consignment. |
| 2. Waste used as input in the recovery operation | |
2.1. Only waste that contained recoverable aluminium or aluminium alloys may be used as input.2.2. Hazardous waste shall not be used as an input except where proof is provided that the processes and techniques specified under Section 3 of this Annex to remove all hazardous properties have been applied.2.3. The following waste shall not be used as an input: (a)
filings and turnings that contain fluids such as oil or oily emulsions; and (b)
barrels and containers, except equipment from end-of-life vehicles, which contain or have contained oil or paints. |
Acceptance control of all waste received (by visual inspection) and of the accompanying documentation shall be carried out by qualified staff which is trained on how to recognise waste that does not fulfil the criteria set out in this Section. |
| 3. Treatment processes and techniques | |
3.1. The aluminium scrap shall have been segregated at source or while being collected and shall have been kept separate or the input waste shall have been treated to separate the aluminium scrap from the non-metal and non-aluminium metal components.3.2. All mechanical treatments (like cutting, shearing, shredding or granulating; sorting, separating, cleaning, de-polluting, emptying) needed to prepare the scrap metal for direct input into final use shall have been completed.3.3. For waste containing hazardous components the following specific requirements shall apply: (a)
input materials that originate from waste electrical or electronic equipment and end-of-life vehicles shall have undergone all treatments required by [F16the EU-derived domestic legislation that transposed— (i)
Article 6 of Directive 2000/53/EC of the European Parliament and of the Council on end-of life vehicles, as last amended by Commission Directive (EU) 2017/2096, and (ii)
Article 8 of Directive 2012/19/EU of the European Parliament and of the Council on waste electrical and electronic equipment (WEEE), as it had effect immediately before 4th July 2018.F16] (b)
chlorofluorocarbons in discarded equipment shall have been captured in an process approved by the competent authorities; (c)
cables shall have been stripped or chopped. If a cable contains organic coatings (plastics), the organic coatings shall have been removed in accordance with the best available techniques; (d)
barrels and containers shall have been emptied and cleaned; (e)
hazardous substances in waste not mentioned in point (a) shall have been efficiently removed in a process which is approved by the competent authority. |
|
ANNEX III
Statement of Conformity with the end-of-waste criteria referred to in Article 5(1)
|
a
Council Regulation (EU) No 333/2011 of 31 March 2011 establishing criteria determining when certain types of scrap metal cease to be waste under Directive 2008/98/EC of the European Parliament and of the Council (OJ L 94, 8.4.2011, p. 2). |
|
| 1. |
Producer/importer of scrap metal: Name: Address: Contact person: Tel. Fax E-mail: |
| 2. |
(a) name or code of the scrap metal category, in accordance with an industry specification or standard:(b) where relevant, main technical provisions of a customer specification, such as composition, size, type and properties: |
| 3. | The scrap metal consignment complies with the specification or standard referred to in point 2: |
| 4. | Quantity of the consignment in tonnes: |
| 5. | A radioactivity test certificate has been established in accordance with national or international rules on monitoring and response procedures for radioactive scrap metal: |
| 6. | The producer of scrap metal applies a quality management system complying with Article 6 of Regulation (EU) No 333/2011a, which has been verified by an accredited verifier or, where scrap metal which has ceased to be waste is imported into the [F17United KingdomF17] , by an independent verifier: |
| 7. | The scrap metal consignment meets the criteria referred to in points (a) to (c) of Articles 3 and 4 of Regulation (EU) No 333/2011a: |
| 8. |
Declaration of the producer/importer of scrap metal: I certify that the above information is complete and correct to my best knowledge. Name: Date: Signature: |
OJ L 312, 22.11.2008, p. 3.
OJ L 218, 13.8.2008, p. 30.
OJ L 312, 22.11.2008, p. 3.
OJ L 218, 13.8.2008, p. 30.