Citation and commencement

1. —(1) These Regulations may be cited as the Road Vehicles (Display of Registration Marks) (Amendment) (EU Exit) (No. 2) Regulations 2020.

(2) Subject to paragraph (3), these Regulations come into force on 1st January 2021.

(3) Regulation 4 comes into force on IP completion day( 2 ).

Amendment of the Road Vehicles (Display of Registration Marks) Regulations 2001

2.The Road Vehicles (Display of Registration Marks) Regulations 2001( 3 ) are amended as follows.

3. In regulation 10 (specifications for registration plates)—

(a) after paragraph (1) insert—

“ (1A) In the case of a vehicle first registered on or after 1st September 2021 the registration plate must conform to the requirements set out in Part A1 of Schedule 2. ” ;

(b) in paragraph (2) after “1st September 2001” insert “but before 1st September 2021”;

(c) in paragraph (3)—

(i) after “paragraph (4)” insert “or (4A)”; and

(ii) before “Part 1” insert “Part A1 or”;

(d) in paragraph (4) after “1st September 2001” insert “but before 1st September 2021”;

(e) after paragraph (4) insert—

“ (4A) Where on or after 1st September 2021 a new registration plate is fixed to a vehicle to which either paragraph (2) or paragraph (3) applies to replace a plate previously fixed thereto, the plate must conform to the requirements set out in Part A1 of Schedule 2. ” ; and

(f) in paragraph (5) before “Part 1” insert “Part A1 or”.

4. In regulation 16 (international distinguishing signs and other material)( 4 ), in paragraph (3), at the end insert “, provided the plate or other device was originally fixed to the vehicle, and complied with the Annex, before IP completion day”.

5. After regulation 17 (optional early use of new-specification plates and prescribed font) insert—

“ Optional early compliance with Schedule 2, Part A1

17A. A new or replacement registration plate fixed to a vehicle on or after the 1st January 2021, and before 1st September 2021, may conform to the requirements set out in Part A1 of Schedule 2. ” .

6. In regulation 18 (saving for vehicles constructed before 1st January 1973), sub-paragraph (a), after “to the Act” insert “and was constructed on or before 1st January 1980”.

7. In Schedule 2 (requirements for registration plates), before Part 1, insert a new Part A1 as follows—

“ PART A1 VEHICLES REGISTERED AND NEW REGISTRATION PLATES FITTED ON OR AFTER 1ST SEPTEMBER 2021 (MANDATORY SPECIFICATION)

1. The plate must be made of retroreflecting material which, as regards its construction, colour and other qualities, complies with the requirements of—

(a) the British Standard specification for retroreflecting number plates published on 28th February 2018 under number BS AU 145e ( 5 ) , or

(b) any other relevant standard or specification recognised for use in an EEA State and which, when in use, offers a performance equivalent to that offered by a plate complying with the British Standard specification,

and which in either case, is marked with the number (or such other information as is necessary to permit identification) of that standard or specification.

2. Where the registration mark is displayed on the front of the vehicle, it must have black characters on a white background.

3. Where the registration mark is displayed on the back of a vehicle, it must have black characters on a yellow background.

4. Subject to the paragraphs below, other than the registration mark, no additional markings may be displayed on a registration plate.

5. Each plate must display below the registration mark additional markings showing—

(a) the number of the British standard or other relevant standard or specification as referred to in paragraph 1;

(b) the name of the supplier or manufacturer of the parts used to assemble the registration plate; and

(c) the name and postcode of the supplying outlet of the assembled registration plate displaying the registration mark.

6. The markings required under paragraph 5 must be—

(a) permanently marked;

(b) non-retroreflecting;

(c) of a single shade of non-retroreflecting colour; and

(d) no more than 10 millimetres in height and no less than 3 millimetres in height.

7. The space between the bottom of the registration mark and any other markings must not be less than 7 millimetres.

8. A border may be displayed on a registration plate where the border is—

(a) permanently marked;

(b) non-retroreflecting;

(c) of a single shade of non-retroreflecting colour without any design, pattern or texture;

(d) positioned no closer than 10 millimetres from the edge of any character of the registration mark;

(e) not positioned above any other markings; and

(f) no more than 5 millimetres in width. ” .

8. In the heading to Schedule 2, Part 1, after “1st September 2001” insert “and before 1st September 2021”.